Fly Of The Week
Partridge & Olive Emerger
Previous Flies
Fly Tying Terms

Partridge & Olive Emerger
A varation on a traditional North Country Spider
By Hans Weilenmann

Materials

Hook:   TMC 2487/2488 (or other make 'grub' hook), Sprite Sproat (or other make sproat bend wet fly hook) #10 - #18. The fly shown was tied on a #12 TMC 2487.

Thread:   Thread: Olive or brown (to match hackle color) 6/0 or 8/0.

Hackle:  Brown or dyed olive partridge back feather. The fly shown was tied using dyed olive feather.

Ribbing:   Dark copper wire.

Abdomen:  Hare's mask or mole, dyed olive. The fly shown was tied using hare's mask.

Thorax:  Brown ostrich herl.

(The materials are listed in the order they are tied in. Instructions assume right-handed tier.)

Tying Steps:

1. Attach the thread immediately behind the eye in three mostly overlapping turns. Prepare partridge feather by removing the fluff, then strip fibers from one side of the stem. (Hold feather by butt, tip facing away from you, dull side on top. Strip fibers from left side.) Lay feather on top of hook, dull side facing up and facing forward over the eye. Tie in hackle on top of hook shank, using the pinch & loop method. Take first wrap over stem, circle shank, come back up and tighten thread with firm pressure straight up. Tie down the stem in touching turns until one quarter down the shank. This will also be the point where the thorax will start later on.

2. Tie in the copper wire, tip touching the snipped off hackle stem to form a level underbody as you make touching turns of thread to well into the bend of the hook. And then two or three touching turns of thread going back towards the eye.

3. Next we want to create the body. As I want this to be an extremely sparsely tied fly (sparse being the operative word in tying any kind of spider/softhackle pattern) I use the touch dub method here. This is the only time in all my flies where I use wax, and sticky wax at that. I can recommend wax produced by John Betts or BT Wax, in either case the tackier of their two 'grades' of wax. Coat about two inches of thread by gently running the wax stick along it. Next take a small clump of hare or mole dubbing and just 'dust' the thread by touching it with the clump of mole. A fuzzy looking thread will be the result. Leave as is. Do not try to twist/rub into a rope.

4. Start winding the body. Make the initial turns towards the bend to the point where the copper wire is tied in to cover any visible thread wraps, then in touching turns towards the point where the thorax will start. Your two inches of hare/mole should be just about right.

5. Take one or two strands of ostrich herl (depending on hook size and quality of herl) and tie in by the butt, then run the thread towards the eye. Leave a small gap for winding the hackle. In keeping with the sparse nature of this fly, ostrich will give the illusion of volume without the unwanted bulk.

6. Wind the ostrich in touching turns towards the eye, then tie off.

7. Using the copper wire rib both abdomen and thorax. I generally prefer to counter-wrap my ribbing material. Make sure to keep the spaces between turns even and the angles identical. Uneven ribbing destroys the looks of a fly like few other errors. The fish may not notice, but it takes as much time to tie a neat fly as it does a sloppy one. I prefer them to be neat ;-) Tie off the copper wire and trim waste of both ostrich and wire.

8. Now, with the thread hanging behind the hackle we are ready for one or two turns of partridge. Clip hackle pliers to the tip of the partridge feather. (For softhackles, with their delicate structure, I like to use the plastic EZ pliers found in Radio Shack and the like.) Make (generally) two turns of partridge in touching turns towards the bend of the hook. End with the hackle pliers straight up (this gives you two complete turns of hackle, resulting in an evenly distributed number of barbules) and trap the partridge with one or two turns of thread. A third turn works through the hackle towards the eye. At this stage snap off the partridge feather. (Sometimes the tip breaks at the hackle pliers, but mostly you get a clean break where it is tied down. Much easier than trying to cut close with your scissors.)


9. Finish the fly with a three-turn whip finish. As there are no materials to tie down at the head, you should end with a very neatly finished fly. Optionally you can tip the head with some thin, penetrating varnish.

10. Front view of the finished fly. Note the sparse hackle, and aim for an even distribution of the fibers.

Fishing suggestions:

I like to fish the Partridge & Olive Emerger casting upstream and across, dead drift in or just below the surface film. Make arial and/or water mends to compensate for variations in the currents between you and the fly's drift.

Most of the takes are visible takes. Look for disturbances in the water surface or "bulging" near where the fly is located to indicate a possible take. Often the surface will be broken as the take occurs. Can be heart stopping stuff ;-)

During hatch situations I sometimes apply a small amount of paste floatant to the hackle only, and fish it as I would a dry fly. It makes for a very good stillborn or cripple imitation. Again, aim for a dead drift presentation upstream and across.

An alternative method of fishing the Partridge & Olive Emerger is a more traditional European downstream swing. ~ Hans Weilenmann

Note: For more terrific flies from all over the world visit Hans website, Flytier's page at: https://www.danica.com/flytier/index.php


For more great flies, check out: Beginning Fly Tying, Intermediate Fly Tying and Advanced Fly Tying.