Anyone have any suggestions for the junction tubing for tube flies. Ive been trying to think of something I can find around the house or at a local store. Im sure that there are several of you that will name some items.
I want to try some big ugly tube flies for smallies,
If you all have some favorite tube flies for smallmouth please post a pic.
thanks,
Seege
I just finished tying this one. I used tubing I’d originally brought for using with jigging spoons. Worked fairly well with the large size hook, a 4/0 Partridge pike hook. I have the feeling it’s a silicone tubing. It has a small inside diameter, which fits tight on the tube and the hook.
I have heard of guys using tubing from an aquarium that is available at most pet shops.
This is one they sell for it commercially, its just small diameter Tygon Tubing…
All ou need is some type of flexible tubing that will fit bot hthe tube and the hook eye.
You can control this a bit by using small eyed hooks (spinnerbait hooks sold for use in lead molds have small eyes).
Bring the hook an the tube to any good sized Aco ro Tru Value and look at the tubing they have in different areas…usually they have rolls of stuff from very small to way too big in the plumbing section, but you’ll find various stull like it all over the store…automotive, hobbies, electrical (heat shrink works, shring it to the hook eye, holds well and is flexible enough for the hook to release and reposition easily), crafts…
Lots of different ways to do this (including not using the tubing at all…many tubes will hold on the knot and you don’t need the flexible tubing). I use cheap plastic cotton swab tubes (have to buy the cheap ones at the dollar store). My clinch knot holds well in the tube without any flex tubing needed
Good Luck!
Buddy
Fireman glad you asked – Im the tube man in our club. I tie tubes on hollow Q tips and use the nut end of a bicycle spoke in my vice to hold the tube. Slide on the Q-tip and tighten the nut to hold it while tying. A nail or bent wire will do the same. I have the smaller tubing to hold the hook, that you can find at my house or send me a PM with your address and Ill send you some. The correct size tubing comes from a feeding tube from a hospital. When we need more Satchel can renew our supply. Look up Tube Flies and Snake Flies on Google. Did you see the smallies in sports page of today paper??? BILL
I tied my favorite streamer with the plastic q tip technique. I didnt have something to mount it on so I had to be gentle not to bend it. Im gonna tie up some woolly buggers with different hook dressings for different fly possibilities. Which would make them convertible flies I believe.
No I didnt see the paper. We have now been residing in MI until our house is ready for move in which will be in late April. I like the idea of the bicycle spoke and the nut. How did the collection go for the flies at the last meeting? I wanted to be there but just couldnt make it due to driving time and other responsibilities.
Bill Pm sent
Thanks for the replies,
Seege
HERE YOU GO I SAW THIS ON HATCH Making Inexpensive Tube Bodies for Tube Flies
by Raymond Tucker (screen name “letumgo”)
I recently started tying a variety of tube flies, but found the price of the tube bodies to be surprisingly expensive. The range of sizes available at the local fly shops also tended to be very limited (only available in one-inch increments.) I set out to find a cheap way of making my own tube bodies that would allow me to easily customize them to suit the flies I intended to tie. Let me share with you a way of making your own custom tube bodies:
Required Tools:
? Ruler
? Sharpie Marker
? Tubing Rotary Cutter
? Fine Sandpaper for Metal (600 grit)
? Single Blade Razor
? Lighter
? Bodkin
Supplies:
Hollow Metal Tubing (1/8” Diam. Or 3/32” Diam. are the most common sizes used in making tube fly bodied, but you may want to try 1/16” Diam. if you are interested in trying tiny versions of tube nymphs). You can purchase metal tubing from hobby and craft shops, or on line. I found a number of sources of very inexpensive metal tubing by searching Google using the following text string “1/8" copper tubing”. You should be able to find small diameter tubing in brass, aluminum and stainless steel. Each of these metals has a different density, allowing you to customize the sink rate of the fly and the zone of the water column you would like to fish.
Keep in mind that you can also use the hollow plastic tubing from the center of a Q-Tip if you want minimum weight and cost. They come in a full range of colors.
One site that seems to carry a wide range of metal tubing is the following: (http://www.hobbylinc.com/prods/rda.htm). Please note that I have not purchased from this site, nor am I in any way associated with this site. I am simply listing it to illustrate what you should be looking for and the variety of options that are available.
A package of twelve 1/8" copper tubes x 12” long sections (by K&S Engineering) will cost around $8.19 (US.) This amount of tubing could make you 144 pieces of 1” long tube fly bodies (which works out to roughly 6 cents each.)
When you purchase finished tube fly bodies in a fly shop, they will usually cost you around $5.00 (US) for 10 pieces x 1” long (which works out to 50 cents each.)
HMH sells an assortment of single-walled hollow plastic tubing used to line the hollow metal tubing to prevent line abrasion and prevent sharp edges from cutting your line. If you are intending to use the 1/8” or 3/32” metal tubes, you will need to buy the “micro” and “small” diameter versions.
The “micro” size plastic tubing will fit through the center of most of the standard metal beads and metal cone-heads used for fly tying, allowing you to easily customize the tube body and add weight.
Making the Tubes:
First measure and mark the metal tubing in the desired lengths that you want to create.
Next – Cut the tubing to length with the rotary tubing cutter.
You should end up with a bunch of pieces like this:
Next sand the ends of the tubing on the emery paper to remove any significant burrs from the cutting operation.
Now its time to assemble the tube bodies by sliding the tubing onto a fine plastic tube and trimming to length. Be sure to let the end of the plastic tube extend past the end of the metal tube so you can later melt it to cover the ends of the metal tube.
Trim the plastic liner to length with the razor and carefully melt the ends to hold the liner in place.
CAUTION - After melting the plastic, you will need to insert a bodkin into the liner to insure the center is still open to allow line through the tube. If the bodkin will not slide easily though the liner, you should cut off the end and carefully re-melt the end. It is important to do the bodkin check before you go through the trouble of creating a fly and then finding that it can not be used because the center is blocked.
In the photo below, I have melted the end of the plastic tubing on the left hand side of the photo. The process is repeated on the other end once the bead has been put in place.
Customization Options:
You can customize the tube by adding any bead (metal or whatever colored craft bead you have on hand – or can “borrow” from your wife…)
Enjoy!
Kenai River fly fishing guides I know use 1 1/4" pieces of plastic stir sticks. The ends are flared with a lighter or alcohol lamp and they are held in the vise with a ball-head needle heavy enough to nearly fill the tubing.
Bunny (flesh) flies are the mainstay of the fleet and they tie them incredibly fast and in huge volumes. A toothpick is used to pin them to the leader.