Tube Fly that Work
Up to this point it has been all about vises,
tube material, basic tying and rigging the flies.
In this last part I’ll leave you with a couple of
patterns that have been very successful for me here
in my local waters. The main thing I have hoped to
accomplish is to spark that imaginative mind in all
of us. I encourage all of you give this a try even
if it’s to simply stick a nail to act as a mandrel
in your present vise with a Q-tip for tube material.
As you have already seen and will see below, there
is no limitation to patterns for the tube fly. Some
of the tried and true standard patterns become even
more effective on a tube. You can even stack deer
hair around the tube with outstanding results. My
tube fly introduction is complete with this last
part, but I will continue to add more in future
articles as I fish them. I strongly recommend anyone
out there who reads this to submit any they have tied
and fished with success to FAOL and share the art with
the fellowship! Who knows some day there may be a Tube
Fly section to FAOL.
The first pattern deals with mocking a familiar pattern
with some alterations. When first looked at most people
think Muddler Minnow. With all that we have explored thus
far think about what colors work well in your area.
Tube Muddler
Step 1. Here I use a soft yellow translucent polyline.
Tied halfway from head and rear are yellow barred hackle
one tied on each side.
Step 2. Add some pearl crystal flash and the fly
takes on highlights that gives that flash in the
water that gets old bucket mouth bass interested.
Step 3. Yep, we’re stacking deer hair. Larger
tubes equal more, much more deer hair. Use lots
of hair and stack top and bottom. Continue to stack
working forward till you have about an eighth of the
tube left. At this point you should have a nice thick
ball of hair.
Step 4. Trim the hair to desired shape. Because the
tube is already of a larger diameter than the typical
hook shaft, you can trim the hair closely and get a
really tight compact look with plenty of diameter
left on the head. Another aspect of deer hair is
it adds positive buoyancy to the tube. This fly is
ready to fish and it does really well with the bass,
small versions do exceptionally well with the large
bluegills. Fixed or free style works well with this
fly, however free style is recommended.
Shimmering Minnow
Step 1. Once again using a soft tube lay a few wraps
of thread about two thirds up from the tail end of the
tube. Also a tube body of a contrasting color to the
material used is recommended.
Step 2. For the first section of the body we are
going to use Orvis Black Shimmer material. Cut it
long enough to extend about one half inch beyond
the tube rear. We are not stacking the material
so cut enough to completely encircle the tube and
tie in place.
Step 3. Cut enough Orvis Chartreuse Shimmer material
to extend a half inch beyond the Black Shimmer Material.
This material is stacked on top with the chartreuse
covering the top half diameter of the tube. This
becomes the overwing. Tie this in place and whip finish.
Step 4. Add eyes to give the live minnow look. It
is stated by many that some species of predator fish
target on the eyes so adding them can enhance your
fishing. This fly is fished strictly fixed style.
It is necessary to align the hook so that the tip
is opposite the overwing. The hook acts as a keel
to help keep the fly right side up.
This concludes the tube fly series. I hope to have
shared some insight on these unique flies. They are
as fun to tie as to fish. For the warm water flyfisher
who targets bass, these flies can be truly deadly.
Whenever I’m streamside and I hand one to a fellow
fly-fisher, it goes something like this:
Flyfisher: " Hey! Where’s the hook!?!?!"
Me: " Well, let me tell you about the wonderful world of tube flies…"
Until next time good fishing!
~ Hillfisher
Originally published c. October 19, 2009 on Fly Anglers Online by Hillfisher.







