-
Bullethead Stone SBS
http://i80.photobucket.com/albums/j1...n/IMG_4816.jpg
Serendipity meet skwala; bullethead version of Bloom's Dead Foam Stone in olive tones. Change colors to suit bug.
hook - Dai Riki 280 #8
thread - UTC 140 olive/yellow
egg sac - foam black
tail - biots olive
body - Congo Hair olive (twisted)
rib - UTC yellow
underwing - landscape fabric
wing - deer hair
legs - rubber medium olive barred
indicator - foam strip
head - deer hair olive
Part 1
mash down barb and attach thread at head (gap width)
http://i80.photobucket.com/albums/j1...n/IMG_4771.jpg
cut, clean and stack a clump of deer hair; measure for length (hook shank)
http://i80.photobucket.com/albums/j1...n/IMG_4773.jpg
trim to length, hold clump on top of hook at head; 2 soft loops right behind hook eye
http://i80.photobucket.com/albums/j1...n/IMG_4774.jpg
pull tight
http://i80.photobucket.com/albums/j1...n/IMG_4777.jpg
and allow hair to spin
http://i80.photobucket.com/albums/j1...n/IMG_4778.jpg
trim butts
http://i80.photobucket.com/albums/j1...n/IMG_4780.jpg
wrap hook shank with thread
http://i80.photobucket.com/albums/j1...n/IMG_4782.jpg
brush a little Super Glue
http://i80.photobucket.com/albums/j1...n/IMG_4783.jpg
-
-
Part 3
and wrap forward; tie off and trim
http://i80.photobucket.com/albums/j1...n/IMG_4797.jpg
wrap ribbing forward; tie off and trim
http://i80.photobucket.com/albums/j1...n/IMG_4799.jpg
prep wing (hook gap width)
http://i80.photobucket.com/albums/j1...n/IMG_4801.jpg
measure for length (hook shank), add a it of Super Glue and tie in
http://i80.photobucket.com/albums/j1...n/IMG_4803.jpg
clean, stack and measure (hook shank) a clump of deer hair; tie in and trim butts
http://i80.photobucket.com/albums/j1...n/IMG_4804.jpg
push hair at head back with finger (try to ensure even distribution around hook)
http://i80.photobucket.com/albums/j1...n/IMG_4809.jpg
pull fibers back over body and tie down
http://i80.photobucket.com/albums/j1...n/IMG_4810.jpg
realize you meant to use yellow thread; switch thread, repeat the previous 2 steps, then tie in legs (you can skip this step if you start with yellow thread - highly recommended)
http://i80.photobucket.com/albums/j1...n/IMG_4813.jpg
add foam indicator, whip finish, SHHAN
http://i80.photobucket.com/albums/j1...n/IMG_4815.jpg
trim out hair on underside and you're done
http://i80.photobucket.com/albums/j1...n/IMG_4817.jpg
Regards,
Scott
-
http://i80.photobucket.com/albums/j1...n/IMG_5572.jpg
Simplified variation on a variation; Furry Foam body instead of twisted poly (Congo Hair) I used previously. Also omitted the wing and just let the hair from the bullethead suffice.
everything's the same up to this point
http://i80.photobucket.com/albums/j1...n/IMG_5543.jpg
trim a piece of Furry Foam and wrap it around the shank (seam on top of hook where underwing will cover it)
http://i80.photobucket.com/albums/j1...n/IMG_5546.jpg
tie down Furry Foam at egg sac
http://i80.photobucket.com/albums/j1...n/IMG_5549.jpg
create a segmented body with thread wraps
http://i80.photobucket.com/albums/j1...n/IMG_5551.jpg
everything else is the same from this point on
http://i80.photobucket.com/albums/j1...n/IMG_5566.jpg
http://i80.photobucket.com/albums/j1...n/IMG_5570.jpg
http://i80.photobucket.com/albums/j1...n/IMG_5568.jpg
serendipitous comparison
http://i80.photobucket.com/albums/j1...n/IMG_5597.jpg
Regards,
Scott
-