having computer issues

i am typing this at work. my pc at home is having a crissis. i over clocked the memory the other day and i believe that i damaged a dimm in the process. will run for about 5 minutes then video lock up and the dreaded shut down. already checked the video card and it is fine. on board video does the same thing. rolled back all of the updates and drivers to a stable restore point. no luck. will remove all of the peripheals tonight but normally this is caused by bad video card (ruled out) or a bad ram chip.

well there is no shame for them as i got them when ddr2 first hit the scene. if it is the mother board north bridge i will switch to a new ddr3 board. hoping it is just a ramm module though.

so if you don't hear from me for a few days you will know what has happened. that should make a few happy for a while.;-)


Eric

Eric,
I had a very similar issue about a year ago. Changed the agraphometer to a different clock position and added a phrone to the leward vestude. Didn't work at first but then I rebooted it with my size 13 Florsheimes and it popped right into phase.

PS: I know, it took me a while to understand the tech talk too, but now, as you can see, I'm totally verplunken.

Mark

Computers have changed, you should seek out Loteck Joe for advise
it has been said that he really know his kidibler pins..

Good luck with that...

BTW: Anybody heard from doughboy?? Hope he is well.....

memtest 386+, follow instruction for the file you download. run on each memory module separately for a couple or 3 hrs to check for errors. or try using the computer with each memory module, like one at a time.

Or get a MAC!!!! Even I can run a Mac!

Nighthawk,

What kind of fly are you trying to tie? :)

Larry ---sagefisher---

take the side off the computer place a box fan their on low turn on computer and un over clock. the mem is over heating. causing it to shut down been their done that lol.

Quote:

---

Originally Posted by Steve Molcsan

Computers have changed, you should seek out Loteck Joe for advise
it has been said that he really know his kidibler pins..

Good luck with that...

BTW: Anybody heard from doughboy?? Hope he is well.....

---

Hey Steve, the last time I learned anything about computers was in 1999. Kidibler pins aren't at all what they used to be. I used to know my way around a floppy disc, but no more.

Nighthawk...you are getting a lot of good advice here:rolleyes:....probably worth about as much as mine.....but what Charlaine said....mine that did that was a laptop with fan vents ...when they got enough dust collected it would overheat...blowing the vents etc. clean would solve the problem....bottom line it could be an overheating issue.

Quote:

---

Originally Posted by sagefisher

Nighthawk,

What kind of fly are you trying to tie? :)

Larry ---sagefisher---

---

A Kingston fly! Must be those cheap imported hackles. :-D

It dumped a RAM chip on me. New one on the way from Newegg should be here Tuesday. Down to one chip so it really likes to lock up. Cooling not an issue with my case. We will see how it goes when the new stuff comes in.

I'd link the kasnorble pandunkle node module to the fryzinc notching quadfarble till it did a complete kasplunk on the frabble port. Now here comes the trickey part just as the kasnerple meter hits 7 tinkledoodles on the padmore scale within less than 22 nano seconds you must very quickly apply exactly 176 snorbles worth of zednip energy to the gordon perk file. DO NOT go over 176 snorbles or the zednips will bark at a sympathetic rate with the oples rod, thus scaring the hell out of the forbles. If that happens then you may as well junk the whole thing.

One other way to re energize the gordon perk file is to set the whole thing on a rock a half mile downstream from the Japanese meltdown untill it glows a bright green. Then Its good after that for about a 1000 years before it will need re-charging .

I like that one.

I just fixed mine with 9 rounds from a 9mm. Bought a new one. Fixed.

Quote:

---

Originally Posted by Gringo

I like that one.

I just fixed mine with 9 rounds from a 9mm. Bought a new one. Fixed.

---

And I like that one! :D