Do any of you have a regular washing and storage ritual that you follow on your breathable waders?
Printable View
Do any of you have a regular washing and storage ritual that you follow on your breathable waders?
I don't wash them. I thoroughly dry them and store in an air/tight storage if I'm not intending to use for a long time, but I live in an area where things tend to deteriorate.
Don't use a liquid detergent on ANY Gore-Tex-type fabric. Tends to start leaks at seams, altho waders are a lot less susceptible than jackets, pants, etc.
I have washed my Hodgman Wadelite stockingfoot waders only once. I have 2 pairs and decided to wash the oldest pair, about 10 years old, in combination with the Revivex Pro-Cleaner followed by spraying with Revivex water repellant. The results have been mixed. I suspect I waited too long before doing the "first" and only wash. Some areas showed good repellency while others not as good. I also bought a bottle of Tectron Polymer Water Proofer. My next experiment will be be to wash and spray my set of hip waders using both the remaining Revivex and Tectron products on respective legs after washing. Should an interesting test. Lay your waders on a horizontal surface when spraying to reduce product loss. Good luck
This is a tip I'll add. Don't store them anywhere near an electric motor. Electric motors give off ozone which can deteriorate rubber products in short order. Not sure how much natural rubber is in modern day waders but to be safe I now store mine in a closet upstairs.
I rarely wash my waders since they are generally kept pretty clean since I mostly fish in clean rivers and streams.
However here are a couple very good videos from Simms on washing and storing their waders: https://www.simmsfishing.com/explore/repairs.html
I would follow the instructions from your wader manufacturer if you have another brand of wader.
Not related to washing them, but good advice:
When "folding" them for storage, make sure you start with the foot end. I have seen others start with the chest end. Then, when air gets captured, they "squeeze" the air out. This is hard on all the seams and may lead to leakage in the seams one day.
Washing waders is not only to clean them. Breathable wader have a DWR (Durable Water Repellency) Coating that has to be renewed. I wash and heat set or retreat my waders with DWR at the end of every season.
Breathable waders should not be washed with any detergent that is scented for leaves a residual material. Most modern detergents contain a UV brighteners so detergents should NOT be used. See instructions later in my post.
Why does a breathable fabric need water repellency? Because when a Gortex garment is coated with water, the water vapor that passes through the Gortex membrane is trapped from escaping to the outside air. So the garment cannot breath. The garment acts just like a solid sheet of plastic and your perspiration is trapped and condenses on the inside of the garment and on your clothing. This is a phenomenon called "wet out". You may think your waders have a small leak but the moisture is sweat condensing inside the waders.
"Wetting out: When water soaks into and spreads across the surface of the fabric, it prevents the breathable layer from working. This is a sign that the durable water repellent (DWR) surface treatment has been compromised. This is when a good cleaning and possibly re-waterproofing can improve your experience."
Wet Out
Read what Gortex says.
Restoring Water Repellency
Here is a primer on how to care for breathable garments by REI.
Rainwear: Durable Water Repellent (DWR) Care
I personally use Nikwax TX.Direct for renewal. It has performed well for me. The product you use to wash your waders is important. It should be a powder and not a liquid, and it should be unscented. That is to prevent any detergent residues that would interfere with the DWR application or seal the Gortex pores. I use Ivory Snow unscented powder. Alternatively, you can use a residue free product like Sport-Wash.
To use the Nikwax TX.Direct, wash your wader or rainwear and rinse well. Hang it up outside and allow the water to drip off. While still damp, spray the wader or garment with Nikwax TX.Direct and cover all areas. Then put in your dryer and dry on the "Permanent Press Low Heat Cycle." Put the suspenders of the waders into a sock to protect them while the DWR sets.
Follow the manufacturer's direction if you use another DWR.
For those of you who are science nerd like me:
The DWR (Durable Water Repellant) coatings like Revivex and Nikewax TX.Direct that renew waders have molecular limbs that point out that repel water. Here is an electron micrograph of some plant surfaces that do the same thing.
http://www.beilstein-journals.org/bj...286-2-19-1.jpg
Lotus leaf scanning electron micrograph below.
http://www.intechopen.com/source/htm...dia/image9.jpg
Nanotechnology solutions for self-cleaning, dirt and water-repellent coatings
Here's a piece of glass that has a coating so it is self cleaning.
http://cdn.physorg.com/newman/gfx/ne...wcoatingtu.jpg
New coating turns ordinary glass into super glass